AT TIME OF PROGRAMMING, ALL REMOTES (UP TO 3) TO BE PROGRAMED/REPROGRAMMED MUST BE PRESENT. The following steps 1-12 are done on a single remote, step 13 is done on all remotes to be programmed. (Up to 3 can be programmed) 1) Get into the car shut the doors and make sure they are unlocked 2) Turn on the ignition (do not turn on the car just the ignition) 3) Press the lock button on remote 4) Turn key to the accessory ON position (your radio works in this mode) 5) Turn on the ignition (do not turn on the car just the ignition) 6) Press the lock button on remote 7) Turn key to the accessory ON position (your radio works in this mode) 8) Turn on the ignition (do not turn on the car just the ignition) 9) Press the lock button on remote 10) Turn key to the accessory ON position (your radio works in this mode) 11) Turn on the ignition (do not turn on the car just the ignition) 12) Press the lock button on the remote, the locks should chirp to indicate that programming mode was entered successfully 13) Press the LOCK button on remote, the doors should chirp again to confirm programming. PRESS THE LOCK BUTTION ON EACH OF THE REMAINING REMOTES TO BE PROGRAMMED (ONE AT A TIME) 14) Turn off the car fully and try locking/unlocking with remote Below step is optional: To turn on/off the chirping when locking/unlocking with remote do the following: 1) Press the trunk release button on the remote and hold it 2) While holding, press the LOCK button on remote and hold it, the led on the remote will flicker for about 1sec 3) After the LED goes off, release both buttons and test it 4) The procedure for chirp on and chirp off is the same, this needs to be done on all remotes otherwise only the one programmed will allow chirping while the others will still be silent or vise versa.

AT TIME OF PROGRAMMING, ALL REMOTES (UP TO 3) TO BE PROGRAMED/REPROGRAMMED MUST BE PRESENT. The following steps 1-12 are done on a single remote, step 13 is done on all remotes to be programmed. (Up to 3 can be programmed) 1) Get into the car shut the doors and make sure they are unlocked 2) Turn on the ignition (do not turn on the car just the ignition) 3) Press the lock button on remote 4) Turn key to the accessory ON position (your radio works in this mode) 5) Turn on the ignition (do not turn on the car just the ignition) 6) Press the lock button on remote 7) Turn key to the accessory ON position (your radio works in this mode) 8) Turn on the ignition (do not turn on the car just the ignition) 9) Press the lock button on remote 10) Turn key to the accessory ON position (your radio works in this mode) 11) Turn on the ignition (do not turn on the car just the ignition) 12) Press the lock button on the remote, the locks should chirp to indicate that programming mode was entered successfully 13) Press the LOCK button on remote, the doors should chirp again to confirm programming. PRESS THE LOCK BUTTION ON EACH OF THE REMAINING REMOTES TO BE PROGRAMMED (ONE AT A TIME) 14) Turn off the car fully and try locking/unlocking with remote Below step is optional: To turn on/off the chirping when locking/unlocking with remote do the following: 1) Press the trunk release button on the remote and hold it 2) While holding, press the LOCK button on remote and hold it, the led on the remote will flicker for about 1sec 3) After the LED goes off, release both buttons and test it 4) The procedure for chirp on and chirp off is the same, this needs to be done on all remotes otherwise only the one programmed will allow chirping while the others will still be silent or vise versa.

AT TIME OF PROGRAMMING, ALL REMOTES (UP TO 3) TO BE PROGRAMED/REPROGRAMMED MUST BE PRESENT. The following steps 1-12 are done on a single remote, step 13 is done on all remotes to be programmed. (Up to 3 can be programmed) 1) Get into the car shut the doors and make sure they are unlocked 2) Turn on the ignition (do not turn on the car just the ignition) 3) Press the lock button on remote 4) Turn key to the accessory ON position (your radio works in this mode) 5) Turn on the ignition (do not turn on the car just the ignition) 6) Press the lock button on remote 7) Turn key to the accessory ON position (your radio works in this mode) 8) Turn on the ignition (do not turn on the car just the ignition) 9) Press the lock button on remote 10) Turn key to the accessory ON position (your radio works in this mode) 11) Turn on the ignition (do not turn on the car just the ignition) 12) Press the lock button on the remote, the locks should chirp to indicate that programming mode was entered successfully 13) Press the LOCK button on remote, the doors should chirp again to confirm programming. PRESS THE LOCK BUTTION ON EACH OF THE REMAINING REMOTES TO BE PROGRAMMED (ONE AT A TIME) 14) Turn off the car fully and try locking/unlocking with remote Below step is optional: To turn on/off the chirping when locking/unlocking with remote do the following: 1) Press the trunk release button on the remote and hold it 2) While holding, press the LOCK button on remote and hold it, the led on the remote will flicker for about 1sec 3) After the LED goes off, release both buttons and test it 4) The procedure for chirp on and chirp off is the same, this needs to be done on all remotes otherwise only the one programmed will allow chirping while the others will still be silent or vise versa.

2004 Chevrolet Malibu Owners Manual Book THESE ITEMS ARE IN GOOD USABLE CONDITION, UNLESS OTHERWISE STATED. SOME OF THESE MANUAL ARE IN NEW OR LIKE NEW CONDITION, HOWEVER THEY ARE USED. IF YOU WANT TO KNOW THE EXACT CONDITION, AND YOU CANNOT TELL BY THE PICTURE EMAIL ME INCLUDES: OWNERS GUIDE\MANUAL

The Acura RL was a full-size luxury sedan produced by the Acura division of Honda for the 1996–2012 model years over two generations. The RL was the flagship of the marque, having succeeded the Acura Legend, and was replaced in 2013 by the Acura RLX. All models of the Legend, RL and RLX lines have been adapted from the Japanese domestic market Honda Legend. The model name "RL" is an abbreviation for "Refined Luxury." The first-generation Acura RL was a rebadged version of the third-generation Honda Legend, and was first introduced to the North American market in 1996, to replace the second-generation Acura Legend. The second-generation Acura RL was a rebadged version of the fourth-generation Honda Legend, introduced to the North American market in September 2004, as a 2005 model. This iteration of the RL received an extensive mid-generational facelift for the 2009 model year, and a further update for 2011. The third-generation debuted for the 2014 model year as the Acura RLX.

The Acura MDX, or Honda MDX as known in Japan and Australia (only the first generation was imported), is a mid-size luxury crossover SUV produced by the Japanese automaker Acura since the 2000. The MDX was the first crossover SUV to have third-row seating. The alphanumeric moniker stands for "Multi-Dimensional luxury". It was introduced as a 2001 model, replacing the slow-selling U.S.-only body-on-frame SLX, based on the Isuzu Trooper. In Japan, it filled a gap when the Honda Horizon (also based on the Trooper) was discontinued in 1999. In 2003, the Honda MDX went on sale in Japan and Australia. For 2009, Acura added a crossover to slot above the MDX, called the ZDX, similar in appearance to the BMW X6

Step 1 Gather the remote for the vehicle on hand. Step 2 Sit in the car with all doors/trunk tightly closed. Step 3 Turn the key to the ON position, marked by “II” on the ignition bezel so the dash lights come on. Step 4 Listen for a quiet click, and then within 5 seconds press the “Lock” button on the remote for 1 second. Step 5 Turn the key to the OFF position, marked by “I” on the ignition bezel so the dash lights go off. If you hear a quiet click in the dashboard after turning switch to "I" then the entire process must be restarted. Step 6 Repeat three more times (for a total of 4 times). Step 7 Upon the 4th turning of the key to “ON”, press the lock button on one remote, the locks will make a cycling sound (clunk), locks will NOT lock or unlock at this point, they will just make a noise. The system is now in programming mode. Do not turn key off. Press lock button 2 more times, and then press unlock. Step 8 Turn ignition completely off and remove the key. Step 9 Step out of car and close door. The remotes should be programmed and work. If you have a trunk/hatch release, the button for this feature needs to be held for a few seconds before the trunk/hatch will “pop”. Tips You must wait for the slight clicking sound in the dash before you press the lock button on the remote. After you reprogram if the Unlock button doesn't work, you must Unlink memory seat by pressing same time unlock and lock button pointed to receiver.(this for TL key fob) Warnings Each step must be completed within 5 seconds. All the doors and rear hatch/trunk must be closed during programming.

Step 1 Gather the remote for the vehicle on hand. Step 2 Sit in the car with all doors/trunk tightly closed. Step 3 Turn the key to the ON position, marked by “II” on the ignition bezel so the dash lights come on. Step 4 Listen for a quiet click, and then within 5 seconds press the “Lock” button on the remote for 1 second. Step 5 Turn the key to the OFF position, marked by “I” on the ignition bezel so the dash lights go off. If you hear a quiet click in the dashboard after turning switch to "I" then the entire process must be restarted. Step 6 Repeat three more times (for a total of 4 times). Step 7 Upon the 4th turning of the key to “ON”, press the lock button on one remote, the locks will make a cycling sound (clunk), locks will NOT lock or unlock at this point, they will just make a noise. The system is now in programming mode. Do not turn key off. Press lock button 2 more times, and then press unlock. Step 8 Turn ignition completely off and remove the key. Step 9 Step out of car and close door. The remotes should be programmed and work. If you have a trunk/hatch release, the button for this feature needs to be held for a few seconds before the trunk/hatch will “pop”. Tips You must wait for the slight clicking sound in the dash before you press the lock button on the remote. After you reprogram if the Unlock button doesn't work, you must Unlink memory seat by pressing same time unlock and lock button pointed to receiver.(this for TL key fob) Warnings Each step must be completed within 5 seconds. All the doors and rear hatch/trunk must be closed during programming.

2007 Acura MDX: Step 1 Gather the remote for the vehicle on hand. Step 2 Sit in the car with all doors/trunk tightly closed. Step 3 Turn the key to the ON position, marked by “II” on the ignition bezel so the dash lights come on. Step 4 Listen for a quiet click, and then within 5 seconds press the “Lock” button on the remote for 1 second. Step 5 Turn the key to the OFF position, marked by “I” on the ignition bezel so the dash lights go off. If you hear a quiet click in the dashboard after turning switch to "I" then the entire process must be restarted. Step 6 Repeat three more times (for a total of 4 times). Step 7 Upon the 4th turning of the key to “ON”, press the lock button on one remote, the locks will make a cycling sound (clunk), locks will NOT lock or unlock at this point, they will just make a noise. The system is now in programming mode. Do not turn key off. Press lock button 2 more times, and then press unlock. Step 8 Turn ignition completely off and remove the key. Step 9 Step out of car and close door. The remotes should be programmed and work. If you have a trunk/hatch release, the button for this feature needs to be held for a few seconds before the trunk/hatch will “pop”. Tips You must wait for the slight clicking sound in the dash before you press the lock button on the remote. After you reprogram if the Unlock button doesn't work, you must Unlink memory seat by pressing same time unlock and lock button pointed to receiver.(this for TL key fob) Warnings Each step must be completed within 5 seconds. All the doors and rear hatch/trunk must be closed during programming.

2002 Chevrolet Malibu Owners Manual Book THESE ITEMS ARE IN GOOD USABLE CONDITION, UNLESS OTHERWISE STATED. SOME OF THESE MANUAL ARE IN NEW OR LIKE NEW CONDITION, HOWEVER THEY ARE USED. IF YOU WANT TO KNOW THE EXACT CONDITION, AND YOU CANNOT TELL BY THE PICTURE EMAIL ME INCLUDES: OWNERS GUIDE\MANUAL